8mm BULKHEAD / Through-Hull Tank Connector

$3.65 + Tax

1 in stock

Product Description

Connect a blumat system to a rain barrel or water storage tank.
Just screw half on the inside of the tank, the other on the outside. The nipple connects to the standard blumat 8 mm water supply/feed line.
You can either start with one of these bulkheads, or a blumat pressure reducer–either of these fittings will “start” your blumat watering system. blumat Classic Jr and blumat xl do not require either.
Use 1/2″ drill bit to puncture hole.

There are no reviews yet.

Be the first to review “8mm BULKHEAD / Through-Hull Tank Connector”

Quick Comparison

Settings8mm BULKHEAD / Through-Hull Tank Connector remove3mm Blumat Tees removeBlumat 8mm Elbows removeBluSoak Drip Tape 10' Plant Ring - Ready to Connect to a Blumat Sensor removeBluSoak Drip Tape to 3mm Blumat Adapter removeBlumat Distribution Drippers- End Pieces, Individual remove
Image
SKUM620810795341F774683PK4098553758543Y487379
Rating
Price$3.65 + Tax$1.10 + Tax$1.10 + Tax$11.00 + Tax$3.00 + Tax$1.29 + Tax
Stock

1 in stock

23 in stock

36 in stock

5 in stock

13 in stock

30 in stock

Availability1 in stock23 in stock36 in stock5 in stock13 in stock30 in stock
Add to cart

Description
ContentConnect a blumat system to a rain barrel or water storage tank. Just screw half on the inside of the tank, the other on the outside. The nipple connects to the standard blumat 8 mm water supply/feed line. You can either start with one of these bulkheads, or a blumat pressure reducer--either of these fittings will "start" your blumat watering system. blumat Classic Jr and blumat xl do not require either. Use 1/2" drill bit to puncture hole.Use these to branch out and run distribution drippers in two directions. You can also put them directly into a 1/2" or 3/4" drip line and install two Blumat sensors.If you have lots of room and can easily make large, round bends; you won't need elbows. If you're in a smaller space though, they will save you lots of room and prevent kinking. See the pictures here for examples of using them to go up and down in raised beds.The BluSoak Drip Tape 10' Plant Ring is a pre assembled unit ready to be connected to your Blumat sensor and is ideal for larger pots that need more water coverage. A 10' soaker hose ready to plug into a Blumat sensor - just push the tubing into the Blumat output hose and wind around the area you'd like to keep moist. Distribution drippers are less expensive in small pots, this one less expensive in larger ones. Keeping more of the potting mix moist lets more roots grow and in effect gives you a much larger pot for the same pot and planting mix cost. This product comes with: 1 BluSoak to 3mm adapter 1 BluSoak End Plug 1 Distribution Dripper 10' of BluSoak 2.0 Drip TapeConnect your Blu Carrot Soaker Hose to a 3mm Blumat line quickly and easily with this adapter. This allows you to connect a Blumat sensor to your BluSoak 2.0 Drip Tape to allow it to detect when the soil is wet enough, and stop feeding the BluSoak with water. When the soil dries near the carrots, then the Blumat carrot (sensor) will begin to feed water back in to the BluSoak line. If the BluSoak isn't close enough to the sensor, make sure to use a distribution dripper (IG15557) in between the sensor and this fitting (example picture shown in third image).Use these to end a Blumat distribution line. The regular distribution drippers have barbs on both sides so you need a way to end them without water dripping out too fast. You can do that with an end cap (IG15509) or with one of these. They are less expensive than the standard drippers and much easier to take on and off than the end caps. The end caps often need pliers to remove but they just pull on and off.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information